Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.
|Published (Last):||20 December 2011|
|PDF File Size:||6.87 Mb|
|ePub File Size:||2.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
This function is designed to allow you to reset selected portions or all of the settings saved in Resets all the functions in the Model Menu the active model memory.
Futaba has notified Horizon Hobby that they will be handling their North American Distribution themselves in addition to some small regional distributers. Curve setting examples The screens shown below are curves created by the fuselage or the reference value. Manaul function is dedicated mixing used in needle adjustment of an engine that uses a fuel mixture control carburetor. This function registers the T12Z user name. Up to 3 rates can be set for each condition.
Do not use the transmitter as it is, send it to the Futaba Service Center. Trim mix function call can be linked to a manua, For a description of the setting method, see Each time you press a trim button, the trim position moves one step.
Always read [Precautions when mounting the receiver and servos] of [Before using]. If you would like, you can freely change combinations of servo output channels, functions aileron, elevator, etcand input controllers sticks, switches, trim levers and trim switches.
After once operating the cursor manuao to button.
Please reference the following link Futaba has provided to re-submit your repair or to obtain product support. Before Use T12Z is operated by 7. Seven types of main wings and three types of tail wings are available for gliders.
FUTABA 12Z Series Manuals
When changing the trim mode, move the by turning the data input dial and set the selection by pushing the enter button. It will prevent the engine from racing dangerously when adjusting the Idle-Up settings. TIMER Each timer may be set for count-down or count The Timer function may be set for any desired time, up operation with a target time. This setting reverses the actual operation This function reverses the operation signal of the signal, but does not change the display of sticks, switches, trimmer levers, and knobs.
When the aileron stick is manipulated, the ailerons and camber flaps perform aileron operation simultaneously and the operation characteristic of the roll axis is improved. The winglet is a vertical or angled extension at the tips of each wing.
Page 64 Mixing rate setting procedure The HR-3 is taken as an example to describe mixing rate setting. To add new models or to call a model already set, use the Model Select function of the Linkage Menu. Although your 12Z protects the model memories with non-volatile EEPROM memory which does not require periodic replacement and not a battery, it still should have regular checkups.
Page 53 Model type Select the model type f r o m a m o n g a i r p l a n ehelicopter, glider, and motor glider.
FUTABA 12Z SERIES INSTRUCTION MANUAL Pdf Download.
futabs Model addition and call Initial setting assigns 1 model to the T12Z transmitter. Got it, continue to print. The T12Z is designed so that the airplane and glider including EP glider model types can handle If the battery fully discharges during During writing, the bar graph moves to the right. Have regular maintenance performed. As an example Trim Mix 1 can be set up for switch can be linked to a stick, etc.
Function, Functions of linkage menu, Function change – Futaba 12Z User Manual
For PCMG3 mode, you can set twelve linear. When using this function, futabaa check initial operation with the propeller removed. Page of Go. Volume Digital trim This transmitter is equipped with digital trims. For retail sales of Futaba, please visit your local dealer or Tower Hobbies.
We hope we will have the opportunity to provide you with great products and outstanding 12a service in the future. Don’t have an account? The Servo Speed setting is used to set the servo delay The End Point function adjusts the left and right for each channel, from channel l to channel